PLUMBING 101: A NECESSITY FOR INSTALLING A BATHTUB

Plumbing 101: A Necessity for Installing a Bathtub

Plumbing 101: A Necessity for Installing a Bathtub

Blog Article

Book A Free Estimate

We've stumbled on this great article pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the net and reckoned it made sense to share it with you in this article.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bathtub isn't exactly rocket science, yet it does require strong plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably difficult task. If the old bathtub is readily easily accessible, the job can move quickly; if you have to open up a wall surface to get rid of the old tub and position the brand-new bathtub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will need a helper to move out the old tub and embeded in the new one. See to it you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a professional to take over a halfway-completed project, it is much better to take into consideration using one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This post will aid you set up a new bathtub in your shower room if you have actually already acquired a new tub and do not require to change the arrangement of your previous water pipelines.
Your devices and product list need to make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Planning for the Installment


    First of all, the supporting frame provided with the bathroom should be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
    Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of every one of the provided washers.
    Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final placement.

    Removing Old Touches


    If you need to change old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be rather problematic as a result of the restricted access that is frequently the situation.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
    Before carrying on to fit the new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

    Mounting the Bath tub


    Utilizing the two wooden boards under its feet, place the bathtub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
    The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the level and also changing the feet on the bathtub until the spirit level reviews degree.
    To install faucets, fit the bottom of the furthest flexible faucet connector to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
    Turn on the water and also inspect all joints and also brand-new pipework for leakages and also tighten them if required. Load the bath tub and also examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
    Finally, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bath tub must wait till the tub has actually been used a minimum of when as this will certainly settle it right into its last position.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existing supply pipelines.
    If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in location in between the tap as well as the sink. Secure the tap in position with the producer supplied backnut. As soon as the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind needs to be linked to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bath tub


    In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to break a stiff seal, causing the water to permeate the wall between the bathroom as well as the tiling, leading to difficulties with wetness and also feasible leakages to the ceiling below.
    You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealer can break rather very early if you do not take into consideration this motion before securing.
    Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the floor tiles using waterproof or water resistant adhesive and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    We had been brought to that report about A Step-by-Step Guide to Installing a Bathtub from someone on another domain. Appreciated our entry? Please share it. Help someone else discover it. Thanks a lot for your time spent reading it.


    Request our emergency plumbing support.

    Report this page